Keyestudio HX711 Load Cell Pressure Sensor Module

  • Pick up from PcGuy Computers Store

Tara 4421, Queensland

Free

  • AusPost Standard

Standard post to your specified address using PakistanPost

 

2-6 Days

From $10

  • AusPost Express

Express post to your specified address using PakistanPost

1-4 Days

From $15

Buy the Keyestudio HX711 Load Cell Pressure Sensor Module in Pakistan for digital weighing and force-measurement projects. Its HX711 24-bit ADC and integrated programmable gain amplifier read low-level signals from compatible bridge-type load cells and provide digital data to a microcontroller.

  • Brand: Keyestudio
  • Model: KS0167
  • Main Chip: HX711
  • ADC Resolution: 24-bit
  • Working Voltage: DC 5V (module specification)
  • Input: Differential load-cell signal
  • Interface: Digital serial (DOUT/DT and SCK/CLK)
  • Compatible Projects: Arduino and compatible microcontrollers
  • Applications: Electronic scales, weight and force measurement
  • Note: Load cell is required separately

₨3,080.00

6 in stock

6 in stock

Description

The Keyestudio HX711 Load Cell Pressure Sensor Module is a 24-bit analogue-to-digital converter and signal-conditioning board designed to read very small signals from strain-gauge load cells. It amplifies the load-cell signal and sends digital measurement data to a microcontroller, making it useful for electronic weighing scales, force measurement and pressure-related DIY projects.

Key Features

24-Bit ADC

Converts small load-cell analogue signals into high-resolution digital measurement data.

Load Cell Interface

Designed for bridge-type strain-gauge sensors commonly used in weighing and force measurement.

Built-In Signal Amplifier

Integrated programmable gain amplifier boosts the low-level differential signal from a load cell.

Two Differential Channels

The HX711 chip provides selectable differential input channels for supported sensor configurations.

Microcontroller Interface

Uses a simple digital serial interface that can be controlled through GPIO pins.

Weighing and Force Projects

Suitable for DIY electronic scales, load monitoring, force experiments and educational prototypes.

Technical Specifications

Brand Keyestudio
Model KS0167
Module Type HX711 load cell amplifier and ADC module
Main Chip HX711
ADC Resolution 24-bit
Module Working Voltage DC 5V (Keyestudio module specification)
Analogue Inputs Two selectable differential input channels (HX711 chip)
Programmable Gain Channel A: 64 or 128; Channel B: 32 (HX711 chip capabilities)
Digital Interface Two-wire serial interface (DOUT/DT and SCK/CLK)
Output Digital measurement data
Sensor Type Bridge-type load cells / strain-gauge sensors
Typical Applications Electronic scales, weight and force measurement projects

Compatible Controllers and Sensors

The module can be used with microcontrollers that provide suitable digital GPIO connections and software support for the HX711 interface. Common project platforms include:

  • Arduino Uno and other compatible Arduino boards
  • ESP32 development boards (check digital logic-level compatibility)
  • ESP8266 development boards (check digital logic-level compatibility)
  • Raspberry Pi GPIO projects with suitable electrical interfacing
  • Compatible bridge-type load cells and strain-gauge weighing sensors

Important: This is the HX711 amplifier/ADC module, not a complete weighing sensor. A compatible load cell, mechanical mounting and calibration are required to measure weight.

Applications

  • DIY digital weighing scales
  • Load-cell based weight measurement
  • Force and load monitoring experiments
  • Robotics and smart automation prototypes
  • Educational electronics and STEM projects
  • Microcontroller-based measurement systems

Connection and Setup Guide

  1. Connect the module’s VCC and GND to a suitable 5V supply and common ground, following the board’s printed labels.
  2. Connect DOUT/DT and SCK/CLK to two available digital GPIO pins on your controller.
  3. Connect the load cell excitation and signal wires to the matching E+/E− and A+/A− terminals as marked on the module and sensor documentation. Wire colours can vary between load cells, so do not rely on colour alone.
  4. Install an HX711 library or the equivalent driver for your selected controller.
  5. Read the raw values, allow the sensor to settle, then calibrate using a known reference weight.
  6. Keep the load cell mechanically mounted as specified by its manufacturer and avoid side loading or overloading it.

Important Before Buying

  • Load cell sold separately: The HX711 module needs a compatible load cell to measure weight. Check the package contents before ordering.
  • 5V module supply: Keyestudio specifies DC 5V for this module. Do not assume the complete breakout is a 3.3V-only board simply because the HX711 IC itself supports a wider supply range.
  • 3.3V controller caution: When using ESP32, ESP8266 or Raspberry Pi, confirm the module’s digital output logic level is safe for the controller’s GPIO. Use suitable level interfacing if required.
  • Calibration required: Accurate readings depend on the load cell, mechanical installation, calibration and software settings.
  • Not a standalone pressure sensor: The module conditions and digitizes a bridge sensor signal; the load cell is the sensing element.

Frequently Asked Questions

What is the Keyestudio HX711 module used for?

It amplifies and converts the small analogue signal from a compatible load cell into digital data. It is commonly used in electronic scales and weight or force measurement projects.

Does this module have a 24-bit ADC?

Yes. It uses the HX711 24-bit analogue-to-digital converter, designed for precision weighing applications.

Does the package include a load cell?

This listing is for the HX711 module. A compatible load cell is required separately unless the package contents explicitly state otherwise.

What is the working voltage of the Keyestudio module?

Keyestudio specifies a DC 5V working voltage for the KS0167 module. Follow the module’s documentation and printed power labels.

Can I use the HX711 with Arduino Uno?

Yes. The module is suitable for Arduino-based load-cell projects. Connect its digital data and clock lines to GPIO pins and use an HX711-compatible library.

Can I connect it to ESP32 or ESP8266?

It can be used in projects with these controllers, but check the module’s digital logic levels before connecting to 3.3V GPIO pins. Use appropriate level interfacing where necessary.

Does the module need calibration?

Yes. Calibrate the connected load cell using a known reference weight. Mounting, sensor capacity and mechanical alignment also affect measurement results.

Can it measure pressure directly?

The HX711 reads signals from a compatible bridge-type sensor. To measure force or pressure, you need a suitable load cell or strain-gauge sensor designed for that measurement.

Why Buy from PcGuy Computers?

  • Electronics and development modules for makers, students and engineers in Pakistan
  • Product details to help you select compatible components
  • Convenient online ordering from PcGuy Computers
  • Support for product-related queries

Buy Keyestudio HX711 Load Cell Module in Pakistan

Build your own digital weighing scale or load-measurement project with the Keyestudio HX711 24-bit load cell amplifier module. Order online from PcGuy Computers for Arduino and compatible microcontroller projects.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “Keyestudio HX711 Load Cell Pressure Sensor Module”

Your email address will not be published. Required fields are marked *