SIM800L GSM GPRS MicroSIM Module

  • Pick up from PcGuy Computers Store

Tara 4421, Queensland

Free

  • AusPost Standard

Standard post to your specified address using PakistanPost

 

2-6 Days

From $10

  • AusPost Express

Express post to your specified address using PakistanPost

1-4 Days

From $15

The SIM800L GSM GPRS MicroSIM Module adds 2G cellular communication to compatible Arduino, ESP32 and embedded electronics projects. It supports SMS, voice calls and GPRS data through a compatible SIM card, with UART serial control using AT commands.

  • Chipset: SIMCom SIM800L
  • Network: 2G GSM / GPRS (quad-band)
  • Frequency: 850 / 900 / 1800 / 1900MHz
  • SIM: MicroSIM socket on listed board
  • Interface: UART serial / AT commands
  • Functions: SMS, voice calls and GPRS data
  • GPRS Speed: Up to 85.6kbps (published maximum)
  • Chip Voltage: 3.4V–4.4V; breakout-board input may differ
  • Applications: IoT, remote monitoring, alerts, tracking and automation
  • Important: 2G-only; confirm local operator service and board power requirements

₨2,200.00

14 in stock

14 in stock

Description

The SIM800L GSM GPRS MicroSIM Module is a compact 2G cellular communication board for embedded electronics, Arduino and IoT projects. Based on the SIMCom SIM800L quad-band GSM/GPRS module, it can provide SMS messaging, voice-call functionality and GPRS data connectivity through a compatible cellular SIM card. A UART serial interface and AT commands allow a microcontroller or host system to control cellular functions for remote alerts, monitoring and automation.

Key Features

Quad-Band 2G GSM

Supports GSM 850, EGSM 900, DCS 1800 and PCS 1900MHz bands. Local operator support must be checked before use.

SMS and Voice

Supports sending and receiving SMS messages and voice communication through supported interfaces and suitable external audio connections.

GPRS Data

Provides packet data connectivity for telemetry and low-bandwidth IoT applications, with a published maximum rate of up to 85.6kbps.

UART Serial Control

Communicates with compatible controllers through serial commands using the SIMCom AT command set.

MicroSIM Interface

The listed module board is designed for a MicroSIM card. Confirm the physical socket and board revision before installation.

Embedded Project Use

Suitable for prototyping cellular alerts, remote monitoring, tracking and automation when the host controller and network are compatible.

Technical Specifications

Product SIM800L GSM GPRS MicroSIM Module
Cellular Chipset SIMCom SIM800L
Network Technology 2G GSM / GPRS
Frequency Bands GSM 850 / EGSM 900 / DCS 1800 / PCS 1900MHz
GPRS Class Multi-slot Class 12 (module specification)
Maximum GPRS Data Rate Up to 85.6kbps uplink and downlink (published maximum)
SIM Interface MicroSIM socket on listed module board; confirm board revision
Control Interface UART serial using AT commands
Supported Functions SMS, voice calls, GPRS data, USSD and TCP/IP-related functions
Chip Supply Voltage 3.4V–4.4V (SIMCom SIM800L specification; board input requirements may differ)
Transmit Power Class 4: 2W at 850/900MHz; Class 1: 1W at 1800/1900MHz
Operating Temperature -40°C to +85°C (module specification)
Module Chip Dimensions 15.8 × 17.8 × 2.4mm (SIM800L module, not necessarily the complete breakout board)

Applications and Project Ideas

  • SMS alert systems: Send event notifications from alarms, sensors and monitoring controllers.
  • Remote monitoring: Report selected sensor readings from remote installations using GPRS.
  • GPS tracking projects: Pair with a compatible GPS receiver to transmit location data over a cellular network.
  • Home and industrial automation: Build SMS-based status notifications or remote-control prototypes.
  • Telemetry: Send low-bandwidth device information to a server or monitoring endpoint.
  • Arduino and embedded development: Experiment with AT commands and cellular communication from supported microcontrollers.

Power and Connection Guidance

  • Use a regulated supply that meets the requirements of the exact breakout board. The SIM800L chip itself specifies a 3.4V–4.4V supply range; do not assume the board accepts 5V unless its documentation confirms it.
  • Cellular transmission creates short, high-current bursts. Design the supply and wiring for the board’s peak current requirement; inadequate power can cause resets, failed network registration or unstable operation.
  • Connect a suitable GSM antenna before attempting network operation.
  • Connect UART TX and RX to a compatible serial interface. Check the board’s logic-level requirements before connecting a 5V microcontroller directly.
  • Insert a compatible, active SIM card with the required service enabled. SIM PIN settings and network registration may need configuration.
  • Use the appropriate baud rate and SIMCom AT commands to test the modem and network connection.

Important Before Buying

SIM800L is a 2G-only GSM/GPRS module, not a 3G, 4G LTE or 5G modem. Confirm that a compatible 2G GSM service is available from your mobile operator and at your intended location before purchasing. Network availability and operator support can change over time. The chip voltage specification is not automatically the input rating of every breakout board; check the actual board’s regulator and printed labels. Antenna, power adapter, SIM card, microcontroller and other accessories are not confirmed as included unless shown in the store’s package details.

Frequently Asked Questions

What does the SIM800L module do?

It adds 2G cellular communication to compatible electronics projects, enabling SMS, voice calls and GPRS data using a supported SIM card and mobile network.

Does SIM800L support 4G or LTE?

No. SIM800L is a 2G GSM/GPRS module. It does not provide 3G, 4G LTE or 5G connectivity.

Which GSM frequency bands are supported?

The SIM800L supports GSM 850, EGSM 900, DCS 1800 and PCS 1900MHz. Your operator must provide compatible 2G service on a supported band.

Can I use it with Arduino or ESP32?

It can be interfaced with compatible Arduino, ESP32 and other microcontroller projects through serial communication. Check UART voltage levels, wiring and power requirements before connecting your controller.

What power supply does SIM800L require?

The SIMCom SIM800L chip specifies a 3.4V–4.4V supply range. The breakout board’s input requirement may differ, and the supply must handle brief high-current transmission bursts. Follow the exact board documentation.

Can it send and receive SMS messages?

Yes. SMS point-to-point messaging is supported, including text and PDU modes, subject to SIM and network service availability.

Does the module include GPS?

No. SIM800L is a GSM/GPRS communication module, not a GPS receiver. A separate compatible GPS module is required for location acquisition.

Will it work with every SIM card in Pakistan?

Not necessarily. The SIM must be active and the mobile operator must still provide compatible 2G GSM service on a supported frequency band in your area. Confirm current local network availability before buying.

Why Buy from PcGuy Computers?

PcGuy Computers provides product information and assistance to help customers choose suitable electronics and development modules. Confirm current availability, package contents and applicable warranty terms with the store before ordering.

SIM800L GSM GPRS MicroSIM Module – Summary

The SIM800L is a compact quad-band 2G GSM/GPRS communication module for embedded projects requiring SMS, voice and low-bandwidth mobile data. Its UART and AT-command interface make it suitable for compatible microcontroller-based IoT, monitoring and automation prototypes. Check 2G network availability and the breakout board’s power requirements before use.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “SIM800L GSM GPRS MicroSIM Module”

Your email address will not be published. Required fields are marked *