9V Battery Holder Alligator Clip Connector
-
Pick up from PcGuy Computers Store
Tara 4421, Queensland
Free
-
AusPost Standard
Standard post to your specified address using PakistanPost
2-6 Days
From $10
-
AusPost Express
Express post to your specified address using PakistanPost
1-4 Days
From $15
9V Battery Holder Alligator Clip Connector connects a standard rectangular 9V / PP3-style battery to suitable circuits using colour-coded alligator clips. Useful for temporary power connections, electronics testing, breadboard experiments and DIY prototyping.
- Battery Connection: Standard 9V battery snap
- Battery Format: 9V / PP3-style
- Output: Alligator / crocodile clips
- Polarity: Colour-coded leads; verify before use
- Connection: Temporary clip-on
- Voltage Regulation: None
- Applications: Testing, prototyping and education
- Battery Included: No
₨440.00
24 in stock
24 in stock
Description
The 9V Battery Holder Alligator Clip Connector is a simple battery lead for connecting a standard rectangular 9V / PP3-style battery to suitable electronic circuits and test points. It has a snap connector for the battery and colour-coded alligator clips for temporary connections during testing, learning and prototyping.
Battery not included. This is a connector lead, not a voltage regulator or a regulated power supply.
Key Features
Standard 9V Battery Snap
Connects to the snap terminals on common rectangular 9V / PP3-style batteries.
Alligator Clip Outputs
Clip onto suitable conductive terminals, wires and test points for temporary circuit connections.
Colour-Coded Leads
Typically uses red and black leads to help identify positive and negative connections. Verify polarity before use.
Quick Connection
Attach and remove the clips without soldering a permanent battery connection into each test circuit.
Useful for Prototyping
Suitable for compatible low-current experiments, component testing and temporary power connections.
Reusable Test Accessory
Can be reused across electronics learning activities and bench tests when handled correctly.
Product Specifications
| Product Name | 9V Battery Holder Alligator Clip Connector |
|---|---|
| Product Type | 9V Battery Connector Lead / Test Lead |
| Battery Connection | Standard 9V battery snap |
| Battery Format | Rectangular 9V / PP3-style |
| Output Connections | Alligator / crocodile clips |
| Polarity Identification | Colour-coded leads (typically red positive and black negative) |
| Connection Style | Temporary clip-on electrical connection |
| Voltage Regulation | None; passes through the battery voltage |
| Battery Included | No |
| Typical Applications | Testing, breadboard experiments, education and DIY electronics |
| Recommended Use | Suitable low-current circuits and temporary test connections |
How the 9V Battery Clip Connector Works
Press the snap connector onto the matching terminals of a compatible 9V battery. The two alligator clips then provide positive and negative connections to a suitable circuit or test point. The clips can be detached when the experiment is complete, making the lead useful for temporary setups.
Alligator clips do not normally plug directly into solderless breadboard holes. For breadboard use, connect them to suitable jumper leads or a compatible power-input connection.
Suitable Uses
- Low-current breadboard experiments using suitable connections
- LED circuits with an appropriate current-limiting resistor
- Testing compatible electronic components and prototypes
- Educational demonstrations of voltage, current and polarity
- Temporary power for suitable buzzer, sensor and small analogue circuits
- Electronics troubleshooting and bench testing
Important Power and Compatibility Notes
This connector does not regulate, convert or stabilise the battery voltage. A 9V battery’s actual terminal voltage changes with its chemistry, condition, charge state and load. If your circuit needs a stable supply, use an appropriate regulator or regulated power source.
Standard rectangular 9V batteries are generally intended for relatively low-current applications. They are usually a poor choice for motors, pumps, large servos and other high-current loads. Choose a power source suited to the current requirements of your project.
- Arduino: Only use a board’s designated external power input if its voltage requirements allow it. Never connect 9V directly to 5V, 3.3V or GPIO pins.
- ESP32 / ESP8266: Do not connect the battery directly to the 3.3V rail or GPIO. Use a suitable regulated supply or supported board input.
- LEDs: Use an appropriate current-limiting resistor; do not connect an ordinary LED directly across the battery.
- Current capability: The current rating of this lead is not specified. Do not assume it is suitable for high-current loads.
Safe Connection and Use
- Confirm that the circuit is designed for the battery’s actual voltage range.
- Identify the required positive and negative connection points.
- Check the lead polarity with a multimeter if necessary, especially before connecting sensitive electronics.
- Attach each clip to the correct point and keep the clips separated.
- Connect the battery snap to a compatible 9V battery.
- Disconnect the battery after testing or when the lead is not in use.
Avoid short circuits: Never allow the positive and negative clips to touch while connected to a battery. A short circuit can cause excessive current, heating and damage to the battery, lead or connected equipment.
What Is Included?
This listing is for the 9V battery snap lead with alligator clip connections. The 9V battery is not included. No voltage regulator, switch or additional power-management module is specified as part of the product.
Frequently Asked Questions
Which battery does this connector fit?
It is designed for the snap terminals found on common rectangular 9V / PP3-style batteries.
Is the 9V battery included?
No. The battery is purchased separately.
What are the alligator clips used for?
They provide temporary connections to suitable wires, terminals, component leads and test points without soldering a permanent connection.
Can I connect it directly to a breadboard?
The alligator clips do not normally plug into breadboard holes. Use suitable jumper leads or a compatible breadboard power-input connection.
Can I use it to power an Arduino?
Only if your particular board supports the battery voltage through its designated external power input. Never connect 9V directly to the 5V, 3.3V or GPIO pins.
Can I connect it directly to an ESP32 or ESP8266?
No, not to the 3.3V rail or GPIO pins. Use an appropriate regulator or a supported development-board power input.
Can it power a motor or pump?
A standard rectangular 9V battery is generally unsuitable for high-current loads such as motors and pumps. Select a power source that meets the load’s current requirements.
Can I use it for an LED circuit?
Yes, if the circuit includes an appropriate current-limiting resistor. Do not connect an ordinary LED directly across a 9V battery.
Which clip is positive?
The leads are typically colour coded, with red for positive and black for negative. Verify polarity before connecting sensitive components.
Does this connector regulate the voltage?
No. It simply connects the battery to the clips and does not regulate or convert the voltage.
Does it have an on/off switch?
No switch is specified for this product. Disconnect the battery to remove power unless your circuit includes a separate switch.
Can the alligator clips touch each other?
No. Keep the clips apart while connected to a battery. Contact between positive and negative can cause a short circuit and overheating.
Why Buy from PcGuy Computers?
| Related Product Range | Battery holders, battery connectors, jumper wires, breadboards and electronics accessories |
|---|---|
| Practical Project Guidance | Product information to help check voltage, polarity and connection requirements |
| Pakistan-Focused Store | Product selection and shopping information for customers in Pakistan |
| Electronics Components | Accessories for testing, prototyping, STEM learning and DIY electronics projects |
The 9V Battery Holder Alligator Clip Connector offers a convenient temporary connection between a standard 9V battery and suitable low-current electronic circuits. Battery not included; check voltage, polarity and current requirements before use.

Arduino Modules & Sensors
Battery Compartments
Component Cases
Electronics Kits
Microcontroller Boards
Project Enclosures
Shields & Hats
Tablets
Laptops
Laptop Accessories
CPU (Processor)
CPU Coolers
GPU (Graphics)
HDD/ SSD (Storage)
MOBO (Motherboard)
PSU (Power Supply)
RAM (Memory)
Keyboard & Mouse Combo
Keyboards
Printers
USB
Reviews
There are no reviews yet.