FS1000A 433MHz RF Wireless Transmitter & Receiver Module
-
Pick up from PcGuy Computers Store
Tara 4421, Queensland
Free
-
AusPost Standard
Standard post to your specified address using PakistanPost
2-6 Days
From $10
-
AusPost Express
Express post to your specified address using PakistanPost
1-4 Days
From $15
Build simple wireless projects with the FS1000A 433MHz RF Transmitter & Receiver Module Set. This pair uses ASK/OOK modulation for one-way digital communication between compatible Arduino and microcontroller projects, including remote switches, alarms and sensor telemetry.
- Set: FS1000A transmitter + compatible 433MHz receiver
- Frequency: 433MHz / approximately 433.92MHz
- Modulation: ASK / OOK
- Communication: One-way / simplex
- Transmitter supply: Typically 3–12V DC; check module version
- Receiver supply: Typically 5V DC
- Data rate: Up to approximately 10kbps
- Interface: Digital data / GPIO
- Applications: Arduino, remote controls, wireless sensors and automation
₨1,320.00
80 in stock
80 in stock
Description
The FS1000A 433MHz RF Wireless Transmitter & Receiver Module Set adds basic one-way wireless data communication to Arduino, microcontroller and DIY electronics projects. It includes an FS1000A transmitter and a compatible 433MHz ASK/OOK receiver for remote commands, wireless sensor readings, alarms and simple automation.
Key Features
433MHz RF Link
Designed for compatible low-power wireless communication, typically around 433.92MHz.
Transmitter + Receiver
Includes one FS1000A transmitter and one compatible 433MHz receiver module.
ASK / OOK Modulation
Uses simple amplitude-based modulation for basic digital data transmission.
Microcontroller Interface
Connects through digital data pins; it does not require an SPI or I2C interface.
Remote Control Projects
Suitable for wireless switches, remote commands, alarms and basic automation prototypes.
Sensor Telemetry
A controller can encode sensor readings and send small data messages to a remote receiver.
How the FS1000A RF Module Works
A microcontroller sends a digital signal to the FS1000A transmitter. The transmitter sends the signal over a 433MHz radio link, and the compatible receiver detects it and provides a data output to the receiving circuit. The modules provide a one-way (simplex) link: the receiver does not send an acknowledgement back.
Transmitter and Receiver Connections
Typical transmitter connections include DATA, VCC and GND, with an antenna connection where provided. The receiver typically has power, ground and digital data output connections. Pin layout can vary between module versions, so check the markings on the actual board before wiring.
- Transmitter supply: commonly specified around 3–12V DC; verify the supplied module before applying power.
- Receiver supply: typically 5V DC for common versions.
- Data interface: digital signal connections to a compatible controller.
- Receiver DATA pins: some boards expose two pins carrying the same signal; they are not necessarily separate channels.
Arduino, ESP32 and Microcontroller Projects
The set can be used with Arduino-compatible boards for sending button commands, switch states and encoded sensor readings. A typical setup uses one controller with the transmitter and another controller with the receiver. Compatible ASK/OOK libraries, such as RadioHead for supported configurations, can help with message framing and decoding.
3.3V GPIO caution: ESP32, ESP8266 and Raspberry Pi GPIO are not 5V tolerant. Check the receiver output level and the transmitter input requirements; use suitable level shifting where necessary.
Applications
- Arduino wireless communication experiments
- Remote control switches and buttons
- Wireless temperature, humidity and soil-moisture sensor nodes
- Door, motion and alarm status projects
- Relay, lighting and pump control prototypes
- Robotics, home automation and STEM learning
The receiver provides a data signal, not a high-current output. Use a suitable microcontroller and relay, MOSFET or motor-driver circuit to operate loads. Do not connect motors, pumps or other high-current devices directly to GPIO.
Range, Antenna and Data Rate
The data rate is commonly quoted up to approximately 10kbps, making the modules suitable for small commands and sensor messages rather than audio, video or high-speed networking. Actual range is installation-dependent and cannot be guaranteed for generic modules. Antenna design, transmitter supply, receiver quality, obstacles, interference, orientation and data rate all affect performance.
A straight quarter-wave wire for approximately 433MHz is about 17.3cm. Connect an antenna only to the designated antenna point where provided. The transmitter itself does not provide packet addressing or error correction, and a basic receiver may produce noise when no valid signal is present; use suitable encoding, validation and repeat handling in software.
Important Compatibility Notes
- This is not Wi-Fi or Bluetooth hardware and does not connect directly to phones, routers or the internet.
- The standard pair is one-way, not a full bidirectional transceiver. Two-way projects need additional suitable radio hardware.
- It is a basic ASK/OOK link; do not assume built-in encryption, addressing, acknowledgement or error correction.
- It is intended for learning and general projects, not as the sole control link for safety-critical equipment.
- Use the 433MHz band in accordance with applicable Pakistan radio regulations; do not assume unrestricted operation or power levels.
Product Specifications
| Product Type | RF Wireless Transmitter & Receiver Module Set |
|---|---|
| Transmitter | FS1000A |
| Receiver | Compatible 433MHz ASK/OOK receiver |
| Operating Frequency | 433MHz band / approximately 433.92MHz |
| Modulation | ASK / OOK |
| Communication | One-way / simplex |
| Transmitter Supply | Typically approximately 3–12V DC; verify board version |
| Receiver Supply | Typically 5V DC |
| Data Rate | Up to approximately 10kbps |
| Receiver Sensitivity | Approximately -105dBm (typical figure; version-dependent) |
| Interface | Digital data / GPIO |
| Antenna | External antenna support where provided |
| Typical Uses | Remote controls, sensors, alarms, automation and wireless data |
What Is Included?
- 1 × FS1000A 433MHz RF transmitter module
- 1 × compatible 433MHz RF receiver module
Microcontrollers, antennas, jumper wires, sensors, power supplies and other accessories are not included unless specifically stated in the package listing.
Frequently Asked Questions
Does this package include both transmitter and receiver?
Yes. The set includes one FS1000A transmitter and one compatible 433MHz receiver module.
What frequency does the module use?
It operates in the 433MHz band, commonly around 433.92MHz.
Can it communicate in both directions?
No. This standard transmitter-and-receiver set provides one-way communication. Bidirectional communication requires additional radio hardware.
Can I use it with Arduino?
Yes. Arduino-compatible controllers can interface through digital pins using suitable ASK/OOK encoding and decoding software.
Does it use SPI or I2C?
No. These basic modules use digital data connections rather than SPI or I2C.
Will it work with ESP32 or ESP8266?
It can be used with suitable interface design. Check signal voltage levels carefully because ESP32 and ESP8266 GPIO pins are not 5V tolerant.
What wireless range can I expect?
Range depends on antenna, supply, receiver version, interference, obstacles and installation. Generic range claims are not guaranteed.
Do I need an antenna?
A suitable antenna can improve performance. A straight quarter-wave wire for 433MHz is approximately 17.3cm, connected to the designated antenna point where provided.
Can it send sensor readings or control a relay?
A microcontroller can encode sensor readings or remote commands for transmission. Use a controller and suitable relay or driver circuit to switch loads; the receiver output is not a high-current output.
Is this Wi-Fi or Bluetooth?
No. It is a basic 433MHz ASK/OOK radio link and does not connect directly to Wi-Fi networks or Bluetooth devices.
Why Buy from PcGuy Computers?
| Pakistan-focused support | Product guidance for electronics and DIY projects in Pakistan. |
|---|---|
| Pakistan-wide shipping options | Shipping options are available subject to destination and service availability. |
| Related project components | Explore Arduino boards, sensors, relay modules and other electronics components for your build. |
| Practical product guidance | Clear product details and compatibility notes to help plan your project. |
Buy the FS1000A 433MHz RF Wireless Transmitter & Receiver Module from PcGuy Computers for Arduino wireless projects, remote control prototypes, sensor telemetry and basic RF experiments in Pakistan.

Arduino Modules & Sensors
Battery Compartments
Component Cases
Electronics Kits
Microcontroller Boards
Project Enclosures
Shields & Hats
Tablets
Laptops
Laptop Accessories
CPU (Processor)
CPU Coolers
GPU (Graphics)
HDD/ SSD (Storage)
MOBO (Motherboard)
PSU (Power Supply)
RAM (Memory)
Keyboard & Mouse Combo
Keyboards
Printers
USB
Reviews
There are no reviews yet.