Keyestudio DS3231 CR1220 Clock Module

  • Pick up from PcGuy Computers Store

Tara 4421, Queensland

Free

  • AusPost Standard

Standard post to your specified address using PakistanPost

 

2-6 Days

From $10

  • AusPost Express

Express post to your specified address using PakistanPost

1-4 Days

From $15

The Keyestudio DS3231 CR1220 Clock Module is an I²C real-time clock for Arduino and compatible electronics projects. It tracks time and date and supports CR1220 battery backup to maintain timekeeping when the main power supply is disconnected.

  • RTC Chip: DS3231
  • Backup Battery: CR1220, 3V (non-rechargeable)
  • Interface: I²C
  • Typical I²C Address: 0x68
  • Supply Range: 3.3V–5.5V (board dependent)
  • Applications: Clocks, alarms, data logging & automation

₨1,540.00

14 in stock

14 in stock

Description

Keyestudio DS3231 CR1220 Real-Time Clock Module

Keep accurate date and time in your Arduino and embedded-electronics projects with the Keyestudio DS3231 CR1220 Clock Module. Built around the DS3231 real-time clock (RTC), it tracks seconds, minutes, hours, day, date, month and year. Its backup-battery input helps preserve timekeeping when the main supply is disconnected.

The module communicates over the I²C interface, making it suitable for digital clocks, timestamped data logging, scheduled automation and other projects that need a reliable time reference.

Key Features

  • DS3231 RTC with temperature-compensated oscillator for accurate timekeeping
  • CR1220 coin-cell backup support for time retention during main-power loss
  • I²C communication for straightforward microcontroller integration
  • Calendar tracking with leap-year compensation through 2100
  • Programmable alarms and 1Hz / 32.768kHz output functions supported by the DS3231
  • Built-in digital temperature sensor
  • Suitable for compatible 3.3V and 5V systems; check your specific board’s pinout and signal levels

Technical Specifications

RTC Chip DS3231
Backup Battery Type CR1220, 3V coin cell (non-rechargeable)
Communication I²C / IIC
Typical I²C Address 0x68
Module Supply Range 3.3V–5.5V (refer to the exact board revision)
Timekeeping Accuracy Approximately ±5ppm (module/operating conditions dependent)
Operating Temperature -40°C to +85°C (DS3231 specification)
Temperature Sensor Accuracy Approximately ±3°C
Clock Outputs 1Hz and 32.768kHz
Calendar Functions Seconds, minutes, hours, day, date, month and year

Typical Applications

  • Arduino and compatible microcontroller clocks
  • Timestamped sensor readings and data loggers
  • Scheduled switching and automation projects
  • Digital calendars, alarms and timers
  • Embedded systems and STEM learning projects

Connection Guide

For a standard four-pin I²C version, connect VCC to a supported supply, GND to ground, SDA to the controller’s SDA pin and SCL to its SCL pin. On an Arduino Uno, the usual I²C pins are A4 (SDA) and A5 (SCL); other boards may use different pins. Confirm the labels and pin order printed on your module before powering it.

Use a compatible DS3231 library and the Arduino Wire library in your sketch. The common I²C address is 0x68. Set the clock once with the correct date and time, then read the RTC values in your project.

Important Notes

  • CR1220 is a non-rechargeable 3V coin cell. Do not attempt to recharge it.
  • Check whether the CR1220 cell is included with the exact supplied package before ordering; package contents can vary.
  • Do not assume every DS3231 breakout has the same layout, pin order or battery-charging circuit. Check the board revision and its documentation.
  • For 3.3V-only controllers, verify the module’s I²C pull-up voltage before connecting SDA and SCL.
  • The DS3231’s temperature reading is intended as a useful onboard measurement, not a replacement for a dedicated precision temperature sensor.

Frequently Asked Questions

1. What does the DS3231 module do?

It keeps track of the current time and date for projects that need a real-time clock.

2. What is the CR1220 battery used for?

The 3V CR1220 coin cell provides backup power so the RTC can continue keeping time when the main supply is removed.

3. Does it work with Arduino Uno?

Yes. A standard I²C DS3231 board can be connected to the Uno using SDA (A4), SCL (A5), VCC and GND. Confirm your board’s pin labels.

4. Can I use it with ESP32 or ESP8266?

It can be used with compatible ESP32 and ESP8266 boards over I²C. Check the breakout’s pull-up voltage and use 3.3V-safe signals.

5. What is the I²C address?

The DS3231 commonly uses the fixed I²C address 0x68.

6. Does the clock retain time after power is disconnected?

Yes, when a suitable CR1220 backup cell is installed and has sufficient charge.

7. Is the CR1220 rechargeable?

No. CR1220 is a non-rechargeable lithium coin cell. Never charge it.

8. Can it be used for data logging?

Yes. Your microcontroller can read the RTC date and time and attach timestamps to sensor readings or saved records.

Why Buy from PcGuy Computers?

PcGuy Computers provides electronics components and development modules for makers, students and DIY projects in Pakistan. Review the product specifications and confirm board and battery details for your intended setup before purchase.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “Keyestudio DS3231 CR1220 Clock Module”

Your email address will not be published. Required fields are marked *