Keyestudio KS0448 4 Channel L298P Motor Driver Shield V1.0

  • Pick up from PcGuy Computers Store

Tara 4421, Queensland

Free

  • AusPost Standard

Standard post to your specified address using PakistanPost

 

2-6 Days

From $10

  • AusPost Express

Express post to your specified address using PakistanPost

1-4 Days

From $15

Buy the Keyestudio KS0448 4-Channel L298P Motor Drive Shield V1.0 for Arduino robotics and multi-motor projects. It supports up to four DC motors, PWM speed adjustment and direction configuration through onboard jumpers, with PH2.0-2P motor connectors and expansion headers. Designed for Arduino UNO R3-style controllers.

  • Model: KS0448 V1.0
  • Driver: L298P
  • Motor Outputs: Up to 4 DC motors
  • Logic Input: DC 5V
  • Motor Supply: DC 7–12V
  • Motor Connectors: PH2.0-2P
  • Speed Control: PWM
  • Direction Setup: 8 jumpers
  • Compatibility: Arduino UNO R3-style shield layout
  • Dimensions: 65 × 50 × 30mm
  • Weight: 29.1g

₨5,500.00

3 in stock

3 in stock

Description

The Keyestudio KS0448 L298P 4-Channel Motor Drive Shield V1.0 is an Arduino-compatible expansion board for controlling up to four DC motors in robotics and automation projects. It uses an L298P-based motor-driving circuit, provides direction and PWM speed control, and connects to motors through anti-reverse PH2.0-2P connectors. Its stackable shield format is designed to fit an Arduino UNO R3-style controller.

Control Four DC Motors from One Arduino Shield

The KS0448 provides four motor outputs, making it useful for multi-motor platforms such as four-wheel robot cars. The Arduino sends logic-level control signals while the shield’s driver circuit handles the motor connections. Each motor’s direction can be configured through the onboard jumper arrangement, and PWM signals are used for speed control.

Four DC Motor Outputs

Connect up to four compatible DC motors for multi-wheel robotics and motion-control builds.

L298P Driver Circuit

Uses the L298P motor-driver solution to switch motor current under controller command.

PWM Speed Adjustment

Use PWM values to adjust motor drive level and tune movement in your Arduino program.

Direction Jumpers

Eight onboard jumpers configure motor rotation direction; their positions can be changed for the required setup.

PH2.0-2P Connectors

Anti-reverse two-pin connectors provide plug-in motor wiring without screw terminals.

Arduino Shield Format

Stacks onto an Arduino UNO R3-style board and exposes additional digital and analog connections.

PWM Speed and Direction Control

The KS0448 uses separate control signals for motor direction and PWM speed. Keyestudio’s example pin assignments are:

Motor A Direction D3, PWM speed D6
Motor B Direction D4, PWM speed D5
Motor C Direction D7, PWM speed D10
Motor D Direction D8, PWM speed D9

For the documented setup, changing the two jumpers beside a motor connector from horizontal to vertical reverses that motor’s direction. The larger the PWM value, the faster the motor is commanded to rotate, within the limits of the motor, supply and driver.

Arduino UNO R3 Stackable Design

The shield is designed to stack directly onto an Arduino UNO R3 controller. The onboard slide switch and BAT power connection are part of Keyestudio’s documented power-up procedure: connect the motor supply as instructed, then switch the board on. Follow the KS0448 wiring guide for the exact power arrangement; do not assume that a USB cable alone is suitable for powering the motors.

Additional Expansion Connections

Besides the motor outputs, the shield brings out additional digital and analog connections using 2.54mm pin and female headers. It also provides a Bluetooth interface compatible with the Keyestudio HM-10 Bluetooth module. Check the pinout before adding sensors or other shields so that you avoid using pins already assigned to motor control.

Technical Specifications

Brand Keyestudio
Model KS0448
Version V1.0
Product Type L298P 4-Channel Motor Drive Shield
Motor Driver Solution L298P
Motor Outputs Up to 4 DC motors
Logic Input Voltage DC 5V
Motor Supply Input DC 7–12V
Logic Working Current Less than 36mA
Driving Part Working Current Less than 4A (manufacturer-stated board specification)
Driver Current Up to 2A (manufacturer-stated L298P capability; operating conditions apply)
Maximum Power Dissipation 50W at T = 75°C (manufacturer-stated)
Motor Connectors Anti-reverse PH2.0-2P
Expansion Header Pitch 2.54mm
Direction Configuration 8 jumpers
Bluetooth Interface Compatible with Keyestudio HM-10 module
Mounting Holes 3 × 3mm diameter
Dimensions 65 × 50 × 30mm
Weight 29.1g
Working Temperature -25°C to +130°C (manufacturer-stated)

Useful for Robotics and Motor Projects

  • Four-wheel-drive Arduino robot cars
  • Mobile robot platforms with multiple DC motors
  • Forward, reverse and turning experiments
  • PWM motor-speed control demonstrations
  • Bluetooth-controlled robotics when paired with a compatible HM-10 module
  • STEM, classroom and DIY motor-control projects

Power and Current Considerations

Keyestudio specifies a DC 7–12V motor-drive input and DC 5V logic input. Choose a regulated, suitable supply for the connected motors and their combined load. Motor startup and stall current can be substantially higher than normal running current, so check the motor’s stall-current rating and the driver’s practical thermal limits before operating several motors together.

The L298P is a bipolar driver and has an internal voltage drop, meaning the motor may receive less voltage than the supply provides. Driver heating also depends on current, load, duty cycle, ventilation and ambient temperature. Do not treat the published maximum figures as a guarantee of continuous operation at those values in every setup.

Motor Compatibility

The KS0448 is presented by Keyestudio as a four-channel DC motor drive shield. It is intended for compatible DC motors; it is not a three-phase brushless motor ESC. A brushless motor requires a suitable electronic speed controller. For stepper motors requiring current regulation or microstepping, select a dedicated stepper driver appropriate to the motor.

Installation and Safe Operation

  • Switch off and disconnect power before changing motor wiring or jumper positions.
  • Stack the shield onto a compatible Arduino UNO R3-style controller with the pins aligned correctly.
  • Connect each motor to its corresponding PH2.0-2P connector.
  • Set the direction jumpers according to the Keyestudio guide.
  • Use the specified motor supply range and verify polarity before powering up.
  • Keep wheels, gears and other moving parts clear of fingers and loose wires during testing.

What Is Included?

This listing is for the Keyestudio KS0448 motor driver shield. The Arduino controller, motors, battery or external power supply, HM-10 Bluetooth module and robot chassis are not confirmed as included; check the package contents if you need any of these accessories.

Why Buy from PcGuy Computers?

PcGuy Computers offers Arduino-compatible development boards, shields, motor drivers, sensors and electronics components for students, makers, educators and robotics projects. The product specifications help you check controller compatibility, motor connections and power requirements before choosing components for your build.

Buy the Keyestudio KS0448 4-Channel L298P Motor Drive Shield V1.0 in Pakistan from PcGuy Computers for Arduino-based multi-motor robotics, four-wheel robot cars and DC motor-control experiments.

Frequently Asked Questions

What is the Keyestudio KS0448?

It is an Arduino-compatible L298P motor drive shield designed to control up to four DC motors.

How many motors can it connect?

Keyestudio specifies four DC motor connections on the KS0448.

Which Arduino board is it designed for?

It is designed to stack onto an Arduino UNO R3-style controller. Check the header layout and pin compatibility of your specific board.

What motor supply voltage does it require?

Keyestudio lists DC 7–12V for the driving section and DC 5V for the logic section.

Can I control motor speed?

Yes. PWM signals are used to adjust motor speed. Keyestudio provides separate PWM control pins for the four motor channels.

Can each motor run in reverse?

Motor direction is configurable using the onboard jumper arrangement and the corresponding direction-control signal.

What connectors are used for the motors?

The shield uses anti-reverse PH2.0-2P connectors for motor connections.

Does it support Bluetooth control?

It has a Bluetooth interface compatible with the Keyestudio HM-10 Bluetooth module. The HM-10 module is a separate accessory unless the package listing says otherwise.

Can I connect additional sensors?

Yes. Additional digital and analog connections are brought out on 2.54mm headers. Check the pin assignments to avoid conflicts with motor-control pins.

Does the shield include an Arduino UNO or motors?

The KS0448 is the motor driver shield. An Arduino controller and motors are separate unless the product package explicitly states that they are included.

Can it drive brushless motors?

No. Three-phase brushless motors require a compatible brushless electronic speed controller. The KS0448 is designed for DC motor driving.

Why might a motor receive less voltage than the supply?

The L298P has an internal voltage drop. The voltage available at the motor can therefore be lower than the input supply, especially under load.

What should I check before connecting four motors?

Check each motor’s operating and stall current, the combined supply requirement, wiring polarity and the driver’s thermal limits. Four motors starting together can demand a high surge current.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “Keyestudio KS0448 4 Channel L298P Motor Driver Shield V1.0”

Your email address will not be published. Required fields are marked *