L9110S DC Dual Motor Drive H Bridge Module

  • Pick up from PcGuy Computers Store

Tara 4421, Queensland

Free

  • AusPost Standard

Standard post to your specified address using PakistanPost

 

2-6 Days

From $10

  • AusPost Express

Express post to your specified address using PakistanPost

1-4 Days

From $15

Buy the L9110S DC Dual Motor Drive H-Bridge Module in Pakistan for controlling two small brushed DC motors or one compatible 4-wire bipolar stepper motor. It supports digital direction control and PWM speed adjustment for Arduino robotics and DIY electronics.

  • Driver: L9110S Dual H-Bridge
  • Motor Supply: 2.5V–12V DC
  • Channels: 2 independent motor channels
  • Continuous Current: Up to approx. 800mA per channel (device specification)
  • Control Inputs: 4 digital logic inputs
  • Control: Direction and PWM speed control
  • Motor Support: 2 brushed DC motors or 1 compatible 4-wire bipolar stepper
  • Applications: Arduino, robot cars, STEM and DIY electronics

₨2,200.00

18 in stock

18 in stock

Description

The L9110S DC Dual Motor Drive H-Bridge Module is a compact two-channel motor driver for controlling two small brushed DC motors independently, or one compatible 4-wire, 2-phase bipolar stepper motor. It operates from a 2.5V–12V DC motor supply and accepts digital control inputs, including PWM signals for speed adjustment. Each channel is commonly specified for up to 800mA continuous output, subject to the board’s thermal and operating conditions.

Key Features

Dual H-Bridge Design

Two independent motor channels let you control a pair of compatible brushed DC motors.

Forward and Reverse

Change the input logic states to reverse the polarity at each motor output and change motor direction.

PWM Speed Control

Apply PWM to a suitable control input to adjust the motor’s average drive level and speed.

Low-Voltage Operation

Designed for a 2.5V–12V DC motor supply, suitable for many small battery-powered robotics projects.

Stepper Motor Support

The two H-bridges can drive one compatible 4-wire, 2-phase bipolar stepper motor using an appropriate sequence.

Simple GPIO Interface

Four logic inputs connect to a microcontroller or compatible digital control circuit.

Technical Specifications

Module / Driver L9110S dual H-bridge motor driver
Motor Supply Voltage 2.5V–12V DC (module specification)
Motor Channels 2 independent H-bridge channels
Continuous Output Current Up to approximately 800mA per channel (device specification)
Peak Current Device datasheets commonly list short-duration peak capability around 1.5A–2A; not a continuous rating
Control Inputs 4 digital logic inputs: A-IA, A-IB, B-IA, B-IB (labels may vary)
Control Method Digital direction control and PWM speed control
Motor Outputs 2 DC motor outputs or 1 compatible 4-wire bipolar stepper
Power Connections VCC and GND

Compatible Motors and Controllers

  • Two small brushed DC motors within the supply-voltage and current limits
  • One compatible 4-wire, 2-phase bipolar stepper motor
  • Arduino boards with suitable digital/PWM outputs
  • ESP8266 and ESP32 development boards when the module input logic and wiring are compatible
  • Other microcontrollers with compatible digital logic levels

The motor supply powers the motor driver and motors; the controller’s GPIO pins provide control signals only. Connect the controller ground and driver ground together. Check the exact board’s input thresholds and pin labels before wiring.

Applications

  • Two-wheel robot cars and small mobile robots
  • Arduino motor-control and PWM learning projects
  • Small automation and motion-control prototypes
  • Battery-powered STEM and educational electronics
  • Compatible bipolar stepper-motor experiments

Connection and Setup Guide

  1. Disconnect power before wiring the module.
  2. Connect the motor supply positive to VCC and its negative to GND. Keep the supply within the specified 2.5V–12V DC range.
  3. Connect the first brushed DC motor to output channel A and the second motor to output channel B. For a stepper motor, use the correct two coil pairs across the two output channels.
  4. Connect the four logic inputs to suitable controller GPIO pins and connect the controller GND to the module GND.
  5. Use the two input signals for each channel to select direction. Apply PWM to a suitable input for speed control; avoid driving both inputs HIGH together unless the chosen control method specifically requires that state.
  6. Start with a low motor supply and a light mechanical load, then test direction and speed before normal operation.

Typical channel logic: one input HIGH and the other LOW drives one direction; reversing those states reverses direction. Both inputs LOW or both HIGH generally place the output in a stop/brake state depending on the IC variant. Confirm the truth table for the actual board/driver before writing control code.

Important Before Buying

  • Current and heat: 800mA per channel is a device-level specification, not a guarantee that every board can sustain this current continuously in all conditions. Heat, PCB layout, airflow and simultaneous motor loading affect the practical limit.
  • Peak is not continuous: Do not size the motor using the short-duration peak current figure. Check its startup and stall current.
  • Voltage drop: H-bridge output voltage is lower than the supply because the driver has an internal voltage drop. A motor may run slower than expected, especially at higher loads.
  • Motor type: This board is for brushed DC motors or a compatible 4-wire bipolar stepper. It is not a brushless motor ESC or an RC servo controller.
  • Separate power: Do not power motors from a microcontroller GPIO pin. Use a suitable motor supply and share ground with the controller.
  • Logic levels: Verify the input logic requirements for your particular board and controller. Do not assume every board revision has identical input protection.
  • Wiring: Check VCC, GND, motor output and input labels on the supplied PCB; layouts and connector positions can vary.
  • Protection: Use a suitable supply and wiring, avoid stalled motors, and disconnect power if the driver becomes excessively hot.

Frequently Asked Questions

What does the L9110S motor driver module do?

It uses two H-bridge channels to control the direction and speed of small brushed DC motors, or to drive one compatible 4-wire bipolar stepper motor.

Can it control two DC motors at the same time?

Yes. It has two independent channels, so it can control two compatible brushed DC motors simultaneously within the module’s voltage and current limits.

What is the operating voltage?

The commonly specified module supply range is 2.5V to 12V DC. Make sure the selected voltage is also suitable for the connected motors.

What is the current rating per channel?

The L9110S is commonly specified for approximately 800mA continuous output per channel. Actual board capability depends on cooling, load and simultaneous operation. Do not treat peak current as a continuous rating.

Can I control motor speed with PWM?

Yes. Apply a suitable PWM signal to a channel’s control input to adjust motor speed. Use the correct input sequence for the required direction.

Is it compatible with Arduino and ESP32?

It can be controlled by Arduino and compatible ESP32/ESP8266 boards through digital GPIO signals. Check the particular module’s logic-input requirements and connect the grounds together.

Can it drive a stepper motor?

It can drive one compatible 4-wire, 2-phase bipolar stepper motor using both H-bridge channels and a suitable stepping sequence. It is not suitable for every stepper motor type.

Can I use it with a brushless motor or servo?

No. It is not a brushless motor ESC or an RC servo controller. Use a driver designed for the specific motor type.

Why Buy from PcGuy Computers?

  • Electronics and STEM components for practical projects
  • Product details to help you check motor and controller compatibility
  • Local Pakistan ordering and customer assistance
  • Components for Arduino, robotics and DIY electronics

Buy L9110S DC Dual Motor Drive H-Bridge Module in Pakistan

Order the L9110S DC Dual Motor Drive H-Bridge Module from PcGuy Computers for small robot cars, Arduino motor-control experiments and compatible DIY projects. Check your motor’s rated voltage and startup/stall current before ordering to ensure it is suitable for this driver.

Customer Reviews

Reviews

There are no reviews yet.

Be the first to review “L9110S DC Dual Motor Drive H Bridge Module”

Your email address will not be published. Required fields are marked *